ProyectECU Berserker, Spartan y Titan
Las nuevas ECUs que ProyectECU tiene para ti
![](https://www.proyectecu.com/wp-content/uploads/BERSERKER-768x576.jpg)
Berserker
Una computadora programable muy completa y compacta!
Control para motor Full Stand alone, Se programa con TunerStudio via Bluetooth.
Control para motor Stand Alone Berzerker
MODELO RECOMENDADO PARA HASTA 8 CILINDROS
La ECU viene lista para usar Sensor CKP tipo VR (reluctante), Hall u Optico.
Consta de MAP interno de 4Bar (hasta 45psi)
El kit incluye:
– ECU Berzerker
– Arnés de 1m 32 hilos
– Conexion Bluetooth
– Software y manuales en area de descargas
Listado de Entradas y Salidas
![](https://www.proyectecu.com/wp-content/uploads/Berserker-1.jpg)
-16×16 3D fuel and ignition maps, with base of either TPS (Alpha-N) or MAP (Speed Density)
-After Start Enrichment
-Rev limiting (Spark based, hard and soft)(flames, explosions)
-Cranking specific enrichment, dwell timing and advance
-General logging through TunerStudio
-High speed tooth logging
-TPS calibration through TunerStudio
-Sensor calibration through TunerStudio (Coolant, IAT and O2)
-Warm Up Enrichment (WUE)
-TPS based acceleration enrichment
-Tacho output
-Fuel pump activation/deactivation (With priming)
-Over dwell and over duty protection
-Battery voltage compensation for dwell and injectors
-Modular wheel decoder support.
-Closed loop boost control
-Open loop VVT control
-Deceleration fuel cut off (DFCO)
-Launch control
-O2 based autotune (Registered version of TunerStudio required)
![](https://www.proyectecu.com/wp-content/uploads/spartanv2-768x576.jpg)
Spartan
Una computadora programable sencilla pero potente!
Control para motor Full Stand alone, Se programa con TunerStudio.
Control para motor Stand Alone Spartan
MODELO RECOMENDADO PARA HASTA 8 CILINDROS
La ECU viene lista para usar Sensor CKP tipo VR (reluctante), Hall u Optico.
Consta de MAP interno de 4Bar (hasta 45psi)
El kit incluye:
– ECU Spartan
– Arnés de 1m 24 hilos
– Cable USB
– Software y manuales en area de descargas
Listado de Entradas y Salidas
![](https://www.proyectecu.com/wp-content/uploads/Spartan-1.jpg)
-16×16 3D fuel and ignition maps, with base of either TPS (Alpha-N) or MAP (Speed Density)
-After Start Enrichment
-Rev limiting (Spark based, hard and soft)(flames, explosions)
-Cranking specific enrichment, dwell timing and advance
-General logging through TunerStudio
-High speed tooth logging
-TPS calibration through TunerStudio
-Sensor calibration through TunerStudio (Coolant, IAT and O2)
-Warm Up Enrichment (WUE)
-TPS based acceleration enrichment
-Tacho output
-Fuel pump activation/deactivation (With priming)
-Over dwell and over duty protection
-Battery voltage compensation for dwell and injectors
-Modular wheel decoder support.
-Closed loop boost control
-Open loop VVT control
-Deceleration fuel cut off (DFCO)
-Launch control
-O2 based autotune (Registered version of TunerStudio required)
![](https://www.proyectecu.com/wp-content/uploads/titanv2-768x576.jpg)
Titan
Una computadora programable extrema y potente!
Control para motor Full Stand alone, Se programa con TunerStudio.
Control para motor Stand Alone Titan
MODELO RECOMENDADO PARA HASTA 8 CILINDROS WMI, VVT
La ECU viene lista para usar Sensor CKP tipo VR (reluctante), Hall u Optico.
Consta de MAP interno de 4Bar (hasta 45psi)
Stepper Opcional
El kit incluye:
– ECU Titan
– Arnés de 1m 48 hilos
– Cable USB
– Software y manuales en area de descargas
Listado de Entradas y Salidas
![](https://www.proyectecu.com/wp-content/uploads/Titan.jpg)
-16×16 3D fuel and ignition maps, with base of either TPS (Alpha-N) or MAP (Speed Density)
-Two stage nitrous control
-After Start Enrichment
-Rev limiting (Spark based, hard and soft)(flames, explosions)
-Cranking specific enrichment, dwell timing and advance
-General logging through TunerStudio
-High speed tooth logging
-TPS calibration through TunerStudio
-Sensor calibration through TunerStudio (Coolant, IAT and O2)
-Warm Up Enrichment (WUE)
-TPS based acceleration enrichment
-Tacho output
-Fuel pump activation/deactivation (With priming)
-Over dwell and over duty protection
-Battery voltage compensation for dwell and injectors
-Modular wheel decoder support.
-Closed loop boost control
-Open loop VVT control
-Deceleration fuel cut off (DFCO)
-Launch control
-O2 based autotune (Registered version of TunerStudio required)